Canyon CNP-WF514A User Manual

1 CNP-WF514 Wireless Broadband Router User Manual

10Device Configuration Before setting up the device, please make sure that the host PC(s) is set on the IP sub-network accessible by CANYON CNP-WF51

11 Internet Connection Wizard 1. Start Internet Configuration Wizard z Internet Configuration Wizard will pop up upon successful login. NOTE: In

12z Select 1 of 7 connection types instructed by ISP or network administrator. z Click on Next to continue or Prev to go back to previous page. z

13z Type in PPPoE Account and PPPoE Password provided from ISP. z Click on Next to continue or Prev to go back to previous page. z Click on Exit t

14z Type in PPTP User Name, PPTP Password, Server IP Address, Primary DNS, and Secondary DNS provided from ISP. z Click on Next to continue or Prev

15z Type in L2TP User Name, L2TP Password, Server IP Address, Primary DNS, and Secondary DNS provided from ISP. z Click on Next to continue or Prev

16z Select a Radio Band type from the drop down box. (802.11b/g is recommended) z Select Radio Mode from the drop down box. (AP+WDS is recommended)

17Status 1. This section displays various router information divided into 3 tabs. 2. The 1st tab displays parameters of WAN/LAN/Wireless connecti

18 3. The 2nd tab displays statistics of packets from WAN port. Click on Refresh to update data monitor table to receive most recent data. z System

19 WAN Setup 1. This section assists user to setup network connection types and their subsidiary functions. The default setting is Dynamic IP conn

2Table of Contents INTRODUCTION...

20NOTE: It is recommended to set MTU value between 1200 and 1500 range. 4. Enter Primary DNS and Secondary DNS IP address if required by ISP provide

21Static IP Setting 1. Type in WAN IP Address, Subnet Mask, Default Gateway, Primary DNS and Secondary DNS address provided by ISP. 2. Click on MA

221. Type in User Name and Password provided by ISP. 2. Type in PPTP Server IP Address. 3. Select connection type. Please follow instructions from

23 1. Type in User Name and Password provided by ISP. 2. Type in PPTP Server IP Address. 3. Select connection type. Please follow instructions fro

242. The 1st tab configures PC(s) connected to device and other settings. Type in System IP Address of device LAN port IP address. This is the defau

25Wireless Basic Setting 1. This section assists user to create a network environment that connects wireless PC(s) to a wired LAN. It also allows

26Security Setting The 2nd tab defines all common security settings for wireless networking. Select one of the Authentication Type from the drop dow

27 z WPA Personal: 1. WPA (Wi-Fi Protected Access) is an advanced security standard that utilizes pre-shared key to authenticate wireless stations

282. Type in Pass Phrase with size ranging from 8 to 63 characters under KEY option. 3. Specify time WPA key must be renewed. The default value is

294. Type in MAC address of PC(s) and optional comments if necessary under Descript box. Click on Add to edit modified rule. 5. An Access Control T

3MAC Filtering Configuration...33 Connection Filtering Configur

304. Type in DTIM Interval frequency between each DTIM (Delivery Traffic Indication Message) broadcast. Lower value result in more efficient network

31 NAT Network Address Translation (NAT) technology allows multiple users at local network to gain access to Internet through a single public IP add

321. Virtual server allows PC(s) located outside of network to be able to access services on PC(s) connected to the device. 2. Type in the descript

335. Select inbound port protocol type between TCP and UDP under Forward Protocol. 6. Type in all of the inbound range of port numbers. Port number

34Connection Filtering Configuration 1. Connection Filtering function blocks certain PC(s) from Internet access based on time. 2. Click on Start/

35URL Filtering Configuration 1. URL Filtering function blocks certain website accesses by specifying keywords. 2. Type in keywords to block PC(s

36 1. Check on Set SPI Firewall State and click Apply to activate SPI Firewall function. 2. Check on Limit the max session of the host and specify

37 1. Click on Start/Stop to turn on/off DynDNS Operation. NOTE: User must sign up on www.dyndns.org to obtain DynDNS service before starting. 2. T

381. The Remote Management function allows user to manage the device through Internet from a remote location. 2. Check Management Port option and t

39Restore Default/Restart System 1. Click on Restore Default to restore all device settings to factory setting. 2. Click on Restart System to rebo

4Thank you for purchasing CANYON CNP-WF514. We sincerely wish you to enjoy the wireless broadband router. It provides user an easy and stable high sp

40Troubleshooting Please refer to the following procedures if CNP-WF514 does not function as it should be. Be advised that the following instruction

41Appendix Technical Specifications Standards IEEE 802.3, IEEE 802.3u, IEEE 802.11g, IEEE802.11b Channels 13 Channels Management Interface Web

5Package Contents Product Image Item Name CNP-WF514 Main Unit Standing Base Power Adapter Warranty Card Quick Guide Documentation CD

6Hardware Overview SYS Power status indicator WAN WAN interface status indicator PC1/PC2/PC3/PC4 LAN interface status indicator DC Jack Connects

7Getting Started Connecting to Device Please follow the steps below to connect the modem and PC(s) with CANYON CNP-WF514: 1. Begin by searching

8Windows Vista Setup 1. Click on Start Æ Settings Æ Network Connections. 2. Right click on Local Area Connection icon and click on Properties. 3.

9by selecting them and clicking on Remove. 8. From DNS Configuration dialog box, remove all entries from DNS server search order box and Domain suff